Container Parts
CIMC Equilink|Container floor Quality Inspection Standard
May 20,2022

The quality inspection items are as follows:


1.Basic dimensions of container floor


The size of the container floor (or shipping container floor) meets the contract requirements, the diagonal difference is less than 2mm, the edge straightness error is less than 0.5mm, and the thickness is controlled at 28±0.75mm. As well as warpage and slot size; container floor warp does not exceed 1mm/1m; container floor twist does not exceed 3mm/1m.


Check whether the container floor has chamfered corners as required by the specifications. If the specifications require chamfered corners but have not fallen, they need to be manually added before going online. (1~1.5mm x 45 degrees, usually on the horizontal side)


The single weight of the container floor meets the grade requirements, 58KG, 62KG and other weights.

container floor thickness detection


2.Packaging and storage of container floors


Check the stockpiling of container floors: indoor, dry, ventilated.


Check whether the container floor outer packaging meets the shipping and shipping requirements.


Horizontal bag: 3 horizontal and 4 vertical straps, vertical bag: 3 horizontal straps and 8 vertical straps.


3.Container floor moisture content


Observe whether the container floor is damp, and the moisture content should be less than 12%.


4.Container floor short span


Export short span up to standard:
H class: ≥8000N,
A class: ≥6500N
B class: ≥5000N,

Bamboo and wood: ≥8000N


6 pieces (305mm*50mm*28mm) are sampled in each batch, and four pieces are required to be qualified, and the average value is not lower than the standard value of the grade.


Maersk test samples three pieces, two of which are qualified as this batch of goods is qualified.


Domestic Shandong board: short span test 58KG: ≥5500N, 62KG passed Maersk test: ≥7500N.


5.Container floor pressing quality


The floor must be 19 layers, the upper and lower three layers are the whole board, no splicing is allowed.


At least ensure that the upper and lower layers have the same longitudinal direction as the box, that is, 3x2 structure; also observe whether there is a 3x3 (upper, middle, and lower three longitudinal layers) or 5x2 (upper and lower five longitudinal layers) structure.


Whether each layer is straight and uniform in thickness , Whether there are voids in the middle and whether there are layers.

19-layer container floor


6. Visual inspection of container floor


Smooth surface, no cracks with a width greater than 2mm and a length greater than 350mm, and no problems such as wormholes and pits.


The upper surface is required to be smooth and free of contamination, and the entire board surface should be similar in color. Observe whether there are serious worm holes, burr groove marks.


The upper and lower plates must be in good condition and level, without scratches, dead joints, holes, decay, sand penetration and other defects; the diameter of the joints is less than 30mm, and the whole surface does not exceed three.


Cracks: There should be no dense small cracks; the width of a single crack should not exceed 3mm, the length should not exceed 300mm, and the number of cracks should not exceed three, and it should be repaired with putty similar to the color of the board. Edge defect: the width is less than 1mm, the depth is less than 2mm, and the cumulative length is less than 50mm.


It is required that the floor is free of resin spills (not oil stains from the outside), because resin spills will affect the strength of the glue there.

visual inspection of container floor


7. Container floor Certificate and Sign Inspection


Check the container floor certificate, whether it is Apitong (Kurning & Hard wood etc.), treatment agent type and treatment time. If the production time is too long, it should be suspected whether there is a problem with this batch of floors.


Must undergo chemical moth-proof treatment (in line with the relevant standards of the Australian Department of Health), based on the supplier's product quality inspection report.


Inspect container floor surfaces and outer packaging for correct stamp markings and for signs of counterfeiting.

container floor packing


According to the above container floor quality inspection standards , strengthen the quality control and continuous improvement to ensure the quality of container floor supply.


In addition to shipping container floor,container corner casting,Container Locking Device,Lashing equipment,Container Corner Post,container Cross Member,container Gasket etc. are all very good container parts sold by CIMC Equilink. Our customers usually buy together with the above products. CIMC Equilink is equipped with professional technicians team to examine the quality of container parts products too. We are proud of being able to offer one-stop service and glad to be your reliable business partner by providing competitive products in quality, lead time and prices.

Share:

Quick Quote

Cannot find what you are looking for?

Write an email to us to consult about your special project, we will assist you to realize your dream product to reality

Write an email
Sign me up!
Please fill in the following form for receiving our monthly product report.
Quick Quote
Please fill in the following form and write a message with your enquiry to us, our sales person will contact you as soon as possible.
  • Upload attachments (file format:pdf、word、Excel、ppt、jpg、png)
    Select file