Container Parts
Wear and Tear on Shipping Container Doors
Dec 14,2022

Shipping Container Door Diagram and Troubleshooting


Shipping containers come in different dimensions, 8ft, 10ft, shipping containers dimensions of 20ft and shipping container dimensions of 40ft being the most common. However, no matter what the size, shipping container parts and mechanics are similar.


1. Doors
2. Lockbox
3. Lockrods, cam keepers, handles
4. Rubber gaskets
5. ISO markings and CSC plate

6. Hinge pins

1.Doors


Two door leaves are each fabricated from two vertical rolled hollow sections and 2 horizontal c section members. The frame is infilled with corrugated steel paneling.


These are normally attached to the rear corner posts each with four drop forged steel hinge blades. The blades allow 270 degree opening which allow the doors to swing back against the container side wall.


(Cargo may shift during transit. Look at the container to make sure that the doors are aligned and level, both top and bottom.  In cases where the container frame is racked and the door gear will not operate correctly.)


2.Lockbox


The lock box is a steel box welded to the right hand door which overlaps a staple welded to the left hand door. A padlock, normally type CISA type 285 66 can then be attached inside the lock box through the staple and is then protected from direct attack, hindering attempts to gain entry to the container.


3.Lockrods, cam keepers, handles


Each door is fitted with 2-4 vertical lock rods to enable container door opening, closing and locking of the doors.

lockrod


At the end of each lock rod (top and bottom) is a cam welded in place which engages with knuckles, also known as cam keepers.


cam keeper


The action of engaging the cams to the keepers forms an anti-racking function.


(In certain cases, often unfortunately too many, contents of the shipping container may have shifted, or containers even dropped, causing shipping container doors and lockrods to warp)


The door handle rotates the lockbar to initiates the container door opening process by forcing the cams out of their keepers.  Each door handle has a door locking handle retainer that slides over the door handle when in locked position.

door handle


4.Rubber gaskets


Rubber gaskets are fitted to the container doors during the manufacturing process and prevent water ingress.


(Door gaskets are designed to present two or more fins against the structure or adjacent door. These are generally flexible but when the gasket is damaged, they may become hard or blocked thus jamming the door closed, or preventing it being closed.)


5.ISO markings and CSC plate


ISO markings and a consolidated data plate allow worldwide intermodal transport when left in place and updated as necessary.


6.Hinge pins

Of course for a door to work, you need hinges.

hinge and hinge pins


(In certain cases when doors are difficult to open, hinge pins and blade are seized due to corrosion.)


Wear and Tear


Shipping containers often take a beating, traveling around the world, being exposed to freezing conditions, and rust due to seawater or when the frost has melted.


Injuries often occur as a result of personnel trying to open and close difficult container doors, often the result of inappropriate techniques being used to open them.


Shipping container doors are not typical doors and there are 4-5 hinges per door.  The hinge pins must be lined up correctly for the doors to be free to fully open and close.


Here are some likely reasons a frozen shipping container door will not open or close. 


The container frame is racked so that the door gear will not operate correctly. This may be caused by cargo shifting during transit. Look at the container to make sure that the doors are aligned and level, both top and bottom.


The hinge pins and blade are seized due to corrosion.


The door gasket has been damaged and is preventing container door opening. Door gaskets are designed to present two or more fins against the structure or adjacent door. These are generally flexible but when the gasket is damaged, they may become hard or blocked thus jamming the door closed, or preventing it being closed.


Water has become trapped between the doors and frozen, particularly relevant to refrigerated cargoes, or containers with moisture releasing cargoes in cold weather.


CIMC Equilink provides all kinds of dry container parts, reefer container parts and iso tank parts. If you are looking for container parts or shipping containers for sale from china , or you just have questions about container declaration and transportation, please visit us by email(info.equilink@cimc.com)or submit a quick quote.

Share:

Quick Quote

Cannot find what you are looking for?

Write an email to us to consult about your special project, we will assist you to realize your dream product to reality

Write an email
Sign me up!
Please fill in the following form for receiving our monthly product report.
Quick Quote
Please fill in the following form and write a message with your enquiry to us, our sales person will contact you as soon as possible.
  • Upload attachments (file format:pdf、word、Excel、ppt、jpg、png)
    Select file